Last Updated: May 5, 2026
Key GRAPHICS & PATTERN LAYERS
Overview
In this lesson, you will learn how to set up and update cuff stripes in the design files to support both 2‑bar and 3‑bar stripe options across 1D, 2D, and 3D panels.
You will begin with the Adult Large cuff stripes, copying the existing cuff into the CuffStripes layer and then adjusting the stripe height. Using the original 2‑inch cuff height as your reference, you will reduce the stripe height by half so it sits correctly at the base of the fold. You will then see how to update 1Ds and 3Ds efficiently by using the symbol‑replace dropdown to swap matching cuff symbols for stripe symbols across all sizes, and how to switch the stripe‑left styling using the cuff stripe graphic style.
For 2Ds, you will remove the incorrect cuff sleeve stripes and rebuild the correct double stripe by using the bottom edge line and a clipping mask so the appearance matches a flat, no‑fold sleeve. You will finish by performing a quality check on all sizes and views and saving the updated file once the cuff stripe system is consistent and aligned.
STEP-by-STep guide
1. Close out the finished cuff work and switch to cuff stripes 0:00
-
The cuff work is already complete, so close out the cuff layers first.
-
Move into the new CuffStripes section.
-
This training covers the new feature that supports:
-
2-bar stripes
-
3-bar stripes
-
-
The goal is to update the stripe artwork so it matches the revised cuff structure.
2. Start with the Adult Large cuff stripe setup 1:42
-
Begin with Adult Large, since it is the easiest case.
-
The cuff stripe uses the same symbol placement as the cuff itself.
-
Copy the original cuff artwork and paste it into the CuffStripes layer.
-
Move the copied artwork aside so you can compare placement and sizing.
3. Resize the stripe to match the new cuff height 2:18
-
The cuff was adjusted, so the stripe must be adjusted too.
-
The original cuff stripe height was 2 inches.
-
Because the foldover is smaller now, the stripe height needs to be reduced by half.
-
Use the design box and measurement tools to:
-
find the current height
-
divide it by 2
-
set the stripe to the new target height
-
-
The stripe should sit right at the base of the fold, because the graphic style handles the rest.
4. Align the stripe on both sides and verify the measurements 4:42
-
Position the stripe so it sits at the base of the fold.
-
Confirm the total height matches the expected measurement.
-
Repeat the same process on the left side.
-
Keep the design box visible for QC while adjusting.
-
The key is to make sure both sides match the revised cuff dimensions exactly.
5. Replace the cuff symbol with the correct stripe symbol 8:37
-
Use the Direct Select tool to click the specific cuff symbol.
-
Open the symbol dropdown and replace it with the matching stripe symbol.
-
This works because the stripe is in the same placement as the cuff.
-
Once replaced, the stripe automatically drops into the correct position.
-
Use the Change Cuffs dropdown to switch between:
-
2-bar
-
3-bar
-
-
This is a fast way to toggle stripe versions without rebuilding the artwork.
6. Update all 1D and 3D panels in bulk 14:55
-
The same symbol-replacement method applies to the 1D and 3D panels.
-
The advantage of using symbols is that multiple instances can be updated at once.
-
Search for the cuff stripe symbol across the layers.
-
Open the relevant layers from the bottom up so you can confirm you are editing the correct symbol.
-
Replace the cuff symbol with the stripe symbol for all matching panels at once.
-
This saves time and prevents repeated manual edits across sizes.
7. Use search and multi-select to replace every matching symbol 17:29
-
Open the panel layers and search for the symbol you want to replace.
-
Select all matching symbols at once.
-
Use the dropdown to replace them with the correct stripe version.
-
Watch the artwork update simultaneously across all selected layers.
-
Important rule:
-
You can replace a symbol with a symbol
-
You cannot replace a symbol with a layer
-
-
If the replace dropdown appears, you are editing the correct object.
8. Move to the 2D cuff stripes and remove the incorrect cuff version 20:50
-
The 2D setup is already partially built, but the current cuff version is incorrect.
-
Remove the old 2D cuff stripe from the cuff layer.
-
Copy the correct 2D cuff stripe into the cuff-sleeve-stripes layer.
-
Keep your layer organization clean:
-
open layers from the bottom up
-
close them from the top down when finished
-
-
This makes it easier to track what has been edited.
9. Paste the 2D stripe into the sleeve and adjust for no-fold construction 23:35
-
Paste the cuff stripe into the 2D sleeve artboard.
-
The first placement will look too high and too thick.
-
That thickness was designed for the folded 1D panels, not the 2D panels.
-
Since the 2D sleeve has no fold, the stripe must be adjusted downward.
-
The graphic style is based from the top of the cuff, so the visible stripe must be rebuilt to fit the flat sleeve.
10. Hide unnecessary mesh layers before refining the stripe 25:35
-
Hide the mesh layers that are not needed for this step.
-
This includes the visible thread/interlock mesh elements.
-
Cleaning up the view makes it easier to edit the stripe shape accurately.
-
The mesh can be restored later when needed.
11. Rebuild the 2D stripe by keeping only the bottom edge 26:59
-
Group the stripe pieces so they are easier to edit.
-
Use the selection tool to delete the extra anchor points and shapes.
-
Keep only the bottom portion of the cuff stripe.
-
The goal is to create a clean line that works for the 2D sleeve.
-
Use the pen tool to sharpen the line where needed.
-
Join points if necessary so the shape looks cohesive.
12. Drop the rebuilt stripe into the clipping mask and QC the result 33:12
-
Once the left and right stripe pieces are correct, place them into the clipping mask.
-
This creates the proper 2D cuff stripe appearance.
-
Check the thickness and alignment to make sure it looks like a real striped cuff.
-
If needed, keep the stripe color visible so it is easy to select and edit.
-
Remember:
-
changing the stripe affects the top color
-
changing the cuff affects the bottom color
-
13. Use graphic styles to switch stripe colors and reset as needed 35:23
-
The stripe and cuff can be styled separately.
-
If you want a different look, switch the graphic style.
-
You can create:
-
two-color versions
-
three-color versions
-
alternate top/bottom combinations
-
-
If the style gets messy, reset it back to the default graphic style.
-
This makes experimentation safe and reversible.
14. Finish the remaining 2D cleanup and refine the linework 37:38
-
Zoom in and hide any layers you do not want to edit.
-
Use the minus tool to remove unwanted areas.
-
Clean up the linework so the stripe looks intentional and polished.
-
The exact shape can vary as long as the final result is clean and visually correct.
-
If you notice an error, unlock the needed layer and correct it before moving on.
15. Run a final QC check and save the updated file 42:44
-
Confirm the cuff stripes are correct for:
-
2D
-
1D
-
3D
-
-
Do a quick quality check to make sure all symbols updated properly.
-
Close out the finished layers.
-
Save the file and version it up to the next revision.
-
The cuff stripe setup is now complete and ready for the next task.